Review of Raijintek Nestor Mid Tower Atx Case
« Introduction and Packaging | Hardware Installation and Clearance Compatibility »
A Closer Wait at the Raijintek Nestor Case
The Raijintek Nestor case measures 239 x 461 x 529mm and its design style is far from the minimalist approach that many manufacturers accept in this price segment. It combines rounded edges with sharp polygonal shapes converging at the center line. The airflow is pocketed from the corners instead of right at the middle where a heavily smoked polycarbonate window is instead.
The front IO is located at the top with the power push/LED located forepart and center. The audio and USB 3.0 headers are positioned on a banking concern to the right while the left side has the reset button and 2 unused (unpunched out) spots for a Firewire and a card reader, giving modders options should they want to add together those. There is a unmarried v.25″ external drive bay covered with a magnetic-locking door.
The intake airflow is gathered entirely from two small meshed areas toward the lesser sides and there are no openings below the front end bezel. The ventilation at the top is located along the sides and some towards the rear.
With the front and top covers removed, mounting supports for 2x 120mm fans are revealed. The front area already has a pair of 120mm fans installed and tin can also back up a pair of 140mm fans. The summit surface area is recessed to accommodate radiators.
Down below, the feet drag the Raijintek Nestor ii.8mm off the basis. There are no rubberized grips here although the soles accept an embossed grilled pattern for added stability on a surface. The power supply intake uses a moving-picture show mesh dust filter insert towards the rear.
At the back there are seven expansion slots, one of which has a reusable cover. Rear ventilation has a diamond pattern and supports a 120mm fan with selection to adjust the mounting height up or down for additional clearance if a radiator is installed at the top.
The side panels are held in place with thumbscrews with a convenient handle in the middle. They are similarly designed in terms of having gratis shapes merely the left side console has a smoked polycarbonate window. The panels accept an elevated surface area providing extra room for taller CPU coolers on the main sleeping room while on the right side console, this actress area provides additional cable direction room.
At that place is a lot of room inside the main bedchamber with the side panels removed. It helps that the peak has extra infinite and that there are no extended v.25″ or three.5″ drive bays on the manner. The stand-offs have already been pre-installed for an ATX motherboard setup then that saves users some time. Micro-ATX users would need to move a few of the bottom standoffs upwardly though.
A large CPU backplate cutout is present and at that place are numerous cable management routing holes present including an 8-pin power connector cable routing above the backplate cutout. What is surprising is that these are grommeted, something that is not often establish on cases priced this low. The cables are as well very long and so even if users try to route them effectually, information technology will have no problem with reaching the motherboard headers.
Another 120mm fan is pre-installed in the rear for exhaust, so that is three fans in full arranged. These fans utilise a 3-pin fan connector.
The 5.25″ bulldoze bay has a half-length mount on the left side and so that in that location is extra working room for the rest of the components. Ane matter I would have preferred withal is for there to be a cable route cutting-out like to the 8-pin CPU surface area for the front console cables. It would take been much cleaner rather than routing all the front IO cables downwards to one of the grommeted spots. Plus it cuts through the five.25″ device area if y'all have a disc drive there.
At that place is also a metal PSU cover running along about the entire length of the bottom area and stops short of total coverage to provide additional radiator clearance for the front. The iii.5″ drive muzzle is housed here which uses two drive caddies. This PSU embrace also has convenient cablevision management routing holes long its length.
Source: https://www.modders-inc.com/raijintek-nestor-review-e50-enthusiast-case/2/
0 Response to "Review of Raijintek Nestor Mid Tower Atx Case"
Post a Comment